Sterling Silver Crescent and Bead Earrings
Resources Required
3" four x one mm sterling silver rectangle wire
20-one 'Λ* head pins
Two turquoise disc beads
1 Vi* 1.7 mm black hollow rubber tube
Two sterling silver ear wires
What tips would you give a commencing artist?
“Do what you adore. Investigate diverse media. Offer with a selective, confined, foundation at first to determine what operates or what isn't going to give you the results you want before you decide to soar into An important outlay of cash and energy.*
-Sally J. Phillips Jewellery Designer
Applications NEEDED
Ruler
Marker
Jeweler's saw or tin snips Safety glasses Difficult, flat surface area Awl
Hammer /is" drill bit
Hand held rotary Instrument, flex shaft, or drill press File
Fantastic grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Scissors
Wire cutters or tin snips Round nose pliers
1.Make use of the ruler to measure and mark two 1 Vi’ items of 4 x 1 mm rectangle sterling silver wire.
2Using a jeweler's noticed or tin snips, Lower the 4 x 1 mm rectangle sterling silver wire into two 1 Vi’ lengths.
3.File Each and every stop in the 1Vi" rectangle wire items to get rid of any burs or rough edges.
If wanted, You need to use the file to round the ends on the rectangle wire items. Make use of a wonderful grit sanding pad to go in excess of the world in which you have filed to easy the edges and remove any file marks.
4.Use the ruler to measure and mark /*." from one end of the one Vi’ parts of rectangle wire and put a mark in the middle of your wire. This is when you can drill the holes to slip The pinnacle pins by.
five.Place with your security glasses!!! Spot the 1 Vi" rectangle wire pieces onto a tough, flat area. Put The purpose with the awl to the mark you designed Vm,' from just one conclude on the rectangle wire items, and firmly strike when on the best of the awl with a hammer. This can make a pilot hole for drilling holes into your rectangle wire.
Sterling Silver Crescent and Bead Earrings
Chapter five
six.Utilizing a /is" drill bit. drill holes into a single finish from the rectangle wire pieces which has a handheld rotary Software, flex shaft, or drill push (even mens ring though even now sporting your safety glasses!).
7.Utilize the file or great grit sanding pad to reduce any burs or tough edges still left from drilling holes in to the rectangle wire pieces.
eight.Curve both of those 1W parts of rectangle wire right into a “C" form using a ring mandrel and rawhide mallet. If you don't have a hoop mandrel and rawhide mallet, use two set of chain nose pliers. Holding 1 set of pliers in Each individual hand, grasp Every single stop from the one Vi* rectangle wire piece Men's Rings While using the pliers and Carefully bend the rectangle wire into a “C* shape. Look at both equally on the C-shaped rectangle wire pieces and adjust the curves so mens ringMen's Rings that they're related in si2e. Set these aside.
nine.Make use of the ruler to measure and Mens Ring mark the rubber tube into four equivalent pieces measuring Vm’ each. Use scissors to chop the rubber tube.
ten.Location the turquoise disc bead onto The pinnacle pin and incorporate 1 V·' piece of the rubber tube, position The top pin through the gap while in the C-shaped rectangle wire, and then increase the opposite V«" piece of rubber tube.
thirteen. Maintain the head pin with the bead, rubber tube, plus the rectangle wire on it in one hand Using the wire that you choose to bent pointing towards you. Using the spherical nose pliers, grip the tip of the head pin wire that may be pointing towards you and roll it far from you (think of turning the ignition critical to begin your car). Launch the pliers from The top pin wire.
At this point, the opening from the loop at the very best of the head pin wire really should nevertheless be large plenty of to slip the ear wire on. When you incorporate the ear wire, use the spherical nose pliers to grasp the loop of The top pin wire and roll it closed. You should utilize the round nose or chain nose pliers to regulate the shape of the loop at the highest of the head pin if you might want to.
eleven. Use the ruler to evaluate and mark /(.’ over the best piece of the hollow rubber tube. With the wire cutters or tin snips, Slice the head pin wire Yu.’ higher than the very best of the hollow rubber tube.
twelve. Use the chain nose pliers to bend The pinnacle pin wire next to the best in the rubber tube in a ninety-degree angle.
fourteen. Repeat these actions for the 2nd earring.